** ** VIA Networking Velocity Family Gigabit Ethernet Adapter ** ** PXERPL BOOTROM ** ** v1.16 May ,2004 ** Introduction: ============= PXERPL combines PXE with RPL and users can choose one they want from bootstrap menu. In general, RPL needs Netware or Windows NT server 3.5/3.51/4.0 to do its boot server, and PXE usually use in Windows NT/2000/XP/2005 or Linux. The PXE of this PXERPL is built by PXE SDK 2.0 build 082, so it full supports PXE Specification 2.1. Contents of the Subdirectory: ============================= PXERPL.TXT This file. GETPR.LOM The bootrom binary file for Lan On Motherboard. GETPR.NIC The bootrom binary file for Network Interface Card. GETND2.DOS The NDIS2 driver require for remote boot. GETND2.CNF The configuration file require for remote boot. PROTOCOL.INI The configuration file require for remote boot. Installation: ============= Before starting the installation process, make sure that the adapter is properly installed and configured. You can use the diagnostic program (A:\DIAG32.EXE) to make sure your connection with the network is correct. PXERPL EEPROM Options ------------------- After POST of BIOS, BootROM will waiting a short time to change boot method. If user strike key, PXERPL will show some advenced menu and you have 4 options in it: Boot Protocol Boot Option Prompt Time RPL Search Time And if no key, PXERPL will boot according EERPOM value. please refer EEPROM.doc to get more informatin about its configuration. 1. Boot Protocol There are 2 options, PXE and RPL. You can specify one which will be booted. 2. Boot Option There are 4 options: Network First, Then Local Local First, Then Network Local Only According BIOS A. Network First, Then Local This option is chosen to boot network by hooking INT 19. Since INT 19 is booting vector, our device is always chosen to boot regardless of IPL priority. B. Local First, Then Network This option is chosen to boot from network by hooking INT 18h. Since INT 18h is boot recovery vector, so only after other local devices with higher IPL prioirty failed to boot successfully then we may boot. C. Local Only This option is chosen to boot from local devices, not to boot from network. D. According BIOS This options is chosen to boot network by PnP/BEV. Whether to boot or not according IPL priority. The proiority for IPL devices is configurable by the user by editing the IPL Priority in BIOS Setup. 3. Prompt Time You can specify the timeout for waiting strikes. There are 3 and 5 seconds. 4. RPL Search Time This option is only active when Boot Protocol is RPL. It sepcifies the timeout of searching RPL server. there are 15, 30, 60 and 120 seconds. If user modifys any option and press to save, PXERPL will write back into EEPROM. Pressing will ignore any modification and booting according EEPROM setting. RPL Setup Procedure: -------------------- 1. The BOOTROM installation procedures are identical in Windows NT Server 3.5, 3.51, 4.0. First, install the Remoteboot Service on the NT Server: Choose "Control Panel\Network\Add Software" and select "Remoteboot Service", follow the screen instruction to install. 2. Use "File Manager" in NT Server 3.5, 3.51 or "Windows Explorer" in NT Server 4.0 to share the following directory: \windows\rpl\rplfiles, suppose \windows is your Windows NT directory. 3. Copy all the MS-DOS 6.22 files as follow: attrib -s -h -r c:\io.sys attrib -s -h -r c:\msdos.sys copy c:\io.sys c:\windows\rpl\rplfiles\binfiles\dos622 copy c:\msdos.sys c:\windows\rpl\rplfiles\binfiles\dos622 copy c:\dos622\*.* c:\windows\rpl\rplfiles\binfiles\dos622 attrib +s +h +r c:\io.sys attrib +s +h +r c:\msdos.sys 4. Copy the NDIS2 driver for "PCI Fast Ethernet Adapter" as follow: copy a:\bootrom\getnd2.dos c:\windows\rpl\bblock\ndis md c:\windows\rpl\bblock\netbeui\getnd2 copy a:\bootrom\getnd2.cnf c:\windows\rpl\bblock\netbeui\getnd2 copy a:\bootrom\protocol.ini c:\windows\rpl\bblock\netbeui\getnd2 5. Run RPLCMD to add a bblock record for the adapter as follow: net start remoteboot ;run in MSDOS prompt rplcmd ;Follow the example below to enter data Adapter Boot Config Profile Service Vendor Wksta [Quit] V Add Del Enum: A VendorName=xxxxxx ;upper 6 digits of your adapter's ethernet ID VendorComment=xx...x ;type your vendor string. optional. Adapter Boot Config Profile Service Vendor Wksta [Quit] B Add Del Enum:A BootName=DOSV1 VendorName=xxxxxx ;upper 6 digits of your adapter's ethernet ID BbcFile=BBLOCK\NETBEUI\GETND2\GETND2.CNF BootCommet=xx...x ;optional string WindowsSize=0 Adapter Boot Config Profile Service Vendor Wksta [Quit] C Add Del Enum:A ConfigName=DOS622V1 BootName=DOSV1 DirName=DOS DirName2=DOS622 FitShared=FITS\DOS622.FIT FitPersonal=FITS\DOS622P.FIT ConfigComment=DOS 6.22 GETND2 DirName3= ;press "Enter" DirName4= ;press "Enter" Adapter Boot Config Profile Service Vendor Wksta [Quit] Q 6. Run "Control Panel\Services", select "Remoteboot Service" and change the "Startup" option to "Automatic". Now reboot NT Server, remoteboot service will be started automatically. 7. Run "Remoteboot Manager" from "Administrative Tools" a. Choose "Remoteboot\New Profile.." to create a Profile Name according to the DOS 6.22 GETND2 configuration. b. Choose "Remoteboot\New Workstation.." to create a Workstation Name according to the profile name and your Adapter Ethernet ID. 8. Now the remoteboot server is ready, boot your workstation with "BOOTROM plug in PCI Fast Ethernet Adapter", then you can access the NT Server from your workstation.